Select Your Region:


all news
20.05.2024 TechnoVector at AutoServiceTec in Italy May 17th to 19th 2024 TechnoVector equipment was featured in Catania
28.03.2024 TechnoVector at DDOR BG Car Show & Motopassion On March 21-27, 2024 TechnoVector 8 contactless machine was featured in the trade show in Serbia
25.03.2024 TechnoVector and iPRO at AMTS 2024 On the 21-24th of March 2024 TechnoVector and iPRO equipment was featured at the show in Hungary.

Wheel washer Tornado AWD (H)

Add to request
Product description

Automatic wheel washer "Tornado-AWD" with the function of water heating

Tornado-AWD automatic wheel washer with the function of water heating has all advantages of the previous models and new technical solutions that allowed us to considerably improve quality of the equipment.

Principal characteristics:

Overall sizes (WxHxD) with a closed door 1105x1561x1338 mm
Overall sizes (WxHxD) with an open door 1105x1561x1674 mm
Overall pack sizes (WxHxD) 1230x770x1500 mm
Wheel width 165-400 mm
Wheel diameter 560-820 mm
Duration of washing 20 s, 40 s, 60 s
Duration of drying 15 s
Water tank capacity 330 l
Nominal water supply of the pump 40 m3/h
Wheel drive rotation speed 685 rpm
Water pressure 4 bar/400 kPa

Grain weight

used to put into the water tank

25 kg

20 kg

Weight without water 330 kg
Maximal weight 390 kg (+/-3%)
 Water heating element capacity 4 kW
Consumed power 10 kW
Air pressure 1 MPa

Tornado-AWD (H) Automatic Wheel Washer Features

Main features:

  • System of wheel stabilization in vertical position;
  • Full noise protection for washing section;
  • Stationary frame for hydraulic lock;
  • Protection for outer surface of disks from damage;
  • Two drive shafts.


Closed cycle wheel washing is used, dirt settles at the bottom. The washer does not require connecting to the water supply and sewerage system and allows you to keep your shop clean and tidy.

Depending on the dirt accumulation level you can select one of the following washing modes: 20 seconds,  40 seconds,  60 seconds.

After that the wheel is automatically dried with compressed air; drying takes 15 seconds. There is also a separate 30-second drying mode.

In the administration mode you can set up any intervals for washing and drying in your wheel washer.

Intended Usage

The Tornado-AWD (H) wheel washer is designed for car service centers and brand service centers to clean wheel disks and tires fast and carefully using water and plastic grains. This makes wheels perfectly clean and almost dry. You can balance clean wheels more easily and more accurately. Moreover, it is more convenient to transport wheels when they are clean.

Maximum size for a wheel for this model of wheel washers is 850mm x 400mm. This allows you to use it not only for motor cars and off-road vehicles but also for small trucks.

Any improper use of the wheel washer such as the washing of tire or rim separately is STRICTLY PROHIBITED because it may cause damages to the machine.

Using Tornado-AWD (H) automatic washers allows you to improve the quality of service while performing tire fitting and wheel balancing, to enhance efficiency of your tire fitting shop and to reduce technicians’ manual labor.


The washer includes a water tank, washing box, electrical unit box, water supply system, air supply system, wheel rotation drive and control system.

Vertical wheel stability is possible thanks to using two drive shafts and some design features in the washing box. This construction allows setting the wheel in the correct position in 2-3 seconds; lockout and tire or disk damage are impossible.

The washing technique involves high-pressure water and grain supply (grains are used as a washing element).

It is a closed cycle washer (250-300 wheels) and thanks to that you need only compressed air and electricity to connect it. The washer does not require connecting to the water supply and sewerage system.

The automatic washer is maintenance-friendly:

  • grains are automatically accumulated into a special container;
  • water and dirt are removed through a drain hole;
  • in the front part of the water tank there is a solid sediment and dirt tank. Thanks to that sediment is accumulated into a place where it can be easily removed from. It is removed from the underpan mechanically.

On the control panel there is an LCD display where information about a current program mode and time left before finishing the operation is shown in a simple way. There is also information about number of washed wheels, a warning if the door of the washing chamber is not closed, a warning to change water and other service messages shown on the display.

 All washers are supplied with:

  • Automatic wheel washer with the function of water heating
  • 25kg of grains,
  • a device to accumulate grains,
  • a rubber mat.

Сертификат  Wheel washer Tornado AWD (H) Сертификат  Wheel washer Tornado AWD (H)
ТORNADO_catalogue.pdf 2.5 Mb Скачать
ТORNADO_AWD.pdf 6.6 Mb Скачать

Comment type is not specified in the component properties.