Menu

News

all news
01/17/2020 Techno Vector at the «Automassan 2020» exhibition in Sweden Techno Vector represents the equipment on the exhibition «Automassan 2020» in Goteborg from 15 to 18 January 2020.
10/08/2019 Techno Vector 8 at the exhibition «AUTO SALON and AUTOWEEK» in Korea Contactless wheel aligner Techno Vector 8 at the exhibition «AUTO SALON and AUTOWEEK» on October 3-6, 2019.
10/01/2019 Techno Vector at the exhibition «AUTOTEC EXPO 2019» in Greece 27-29 of September 2019, Techno Vector equipment was represented at the AUTOTEC EXPO 2019 in Paianía (Greece)

Wheel washer Tornado AWD


How to Buy?
(0)
0 из 5 Оценок: 0.
Product description
Certificates
Instruction

Automatic wheel washer "Tornado-AWD"

Tornado-AWD automatic wheel washer has all advantages of the previous models and new technical solutions that allowed us to considerably improve quality of the equipment.


Principal characteristics:

Overall sizes (WxHxD) with a closed door 1105х1561х1338 mm
Overall sizes (WxHxD) with an open door 1105х1561х1674 mm
Overall pack sizes (WxHxD) 1230х1770х1500 mm
Wheel width 165-400 mm
Wheel diameter 560-820 mm
Duration of washing 20 s, 40 s, 60 s
Duration of drying 15 s
Water tank capacity 330 l
Nominal water supply of the pump 40 m3/h
Wheel drive rotation speed 685 rpm
Water pressure 4 bar/400 kPa

Grain weight

used to put into the water tank

25 kg

20 kg

Weight without water 330 kg
Maximal weight 390 kg (+/-3%)
Consumed power 6 kW
Air pressure 1 MPa


Tornado-AWD Automatic Wheel Washer Features

Main features:

  • System of wheel stabilization in vertical position;
  • Full noise protection for washing section;
  • Stationary frame for hydraulic lock;
  • Protection for outer surface of disks from damage;
  • Two drive shafts.

Washing

Closed cycle wheel washing is used, dirt settles at the bottom. The washer does not require connecting to the water supply and sewerage system and allows you to keep your shop clean and tidy.

Depending on the dirt accumulation level you can select one of the following washing modes: 20 seconds,  40 seconds,  60 seconds.

After that the wheel is automatically dried with compressed air; drying takes 15 seconds. There is also a separate 30-second drying mode.

In the administration mode you can set up any intervals for washing and drying in your wheel washer.

Intended Usage

The Tornado-AWD wheel washer is designed for car service centers and brand service centers to clean wheel disks and tires fast and carefully using water and plastic grains. This makes wheels perfectly clean and almost dry. You can balance clean wheels more easily and more accurately. Moreover, it is more convenient to transport wheels when they are clean.

Maximum size for a wheel for this model of wheel washers is 850mm x 400mm. This allows you to use it not only for motor cars and off-road vehicles but also for small trucks.

Any improper use of the wheel washer such as the washing of tire or rim separately is STRICTLY PROHIBITED because it may cause damages to the machine.

Using Tornado-AWD automatic washers allows you to improve the quality of service while performing tire fitting and wheel balancing, to enhance efficiency of your tire fitting shop and to reduce technicians’ manual labor.


Design

The washer includes a water tank, washing box, electrical unit box, water supply system, air supply system, wheel rotation drive and control system.

Vertical wheel stability is possible thanks to using two drive shafts and some design features in the washing box. This construction allows setting the wheel in the correct position in 2-3 seconds; lockout and tire or disk damage are impossible.

The washing technique involves high-pressure water and grain supply (grains are used as a washing element).

It is a closed cycle washer (250-300 wheels) and thanks to that you need only compressed air and electricity to connect it. The washer does not require connecting to the water supply and sewerage system.

The automatic washer is maintenance-friendly:

  • grains are automatically accumulated into a special container;
  • water and dirt are removed through a drain hole;
  • in the front part of the water tank there is a solid sediment and dirt tank. Thanks to that sediment is accumulated into a place where it can be easily removed from. It is removed from the underpan mechanically.

On the control panel there is an LCD display where information about a current program mode and time left before finishing the operation is shown in a simple way. There is also information about number of washed wheels, a warning if the door of the washing chamber is not closed, a warning to change water and other service messages shown on the display.

All washers are supplied with:

  • Automatic wheel washer,
  • 25kg of grains,
  • a device to accumulate grains,
  • a rubber mat.

tornado_awd.pdf 926.4 Kb Скачать
tornado_moyki_koles_katalog_2020.pdf 21.1 Mb Скачать

Comment type is not specified in the component properties.